rubber hose on transmission line

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • Can you repair transmission line with rubber hose?

    2020-2-11 · Hereof, can I use rubber hose for transmission cooling lines? You could run it all in rubber and be fine so long as it doesn't chaffe or get pinched. If you are that concerned you could run braided hose with AN fittings but it can get pricey quick. Rubber trans line will hold just fine.

    Get Price
  • Can I use rubber hose for transmission cooler

    2020-1-22 · In this way, can you repair transmission line with rubber hose? Yes it HAS to be designed for hydraulic fluid. Trans fluid & regular rubber fuel line aren't compatible, as it will swell it & leak. If I have to use any hose on the transmission line, I usually flare the steel line before I slip on the rubber hose, it helps to keep the hose from blowing off.

    Get Price
  • Rubber hose for trans cooler line repair?? | Team

    2014-12-13 · 90 percent of new cars now days use rubber hoses to connect the transmission lines to the radiator and back. Trucks however, typically do not. If your running a length of hose to repair a leak, you will be fine. I do recommend using high pressure clamps.

    Get Price
  • Rubber hose for trans cooling line | Ford Mustang

    2017-2-2 · Its common to use short sections of rubber hose (rated for trans fluid) to connect trans lines into an external cooler, since you need some flexibility to route up through the radiator support. However, the primary lines running from the transmission to the front of the car really should be one piece steel lines.

    Get Price
  • Hoses/Lines & Clamps Transmission Fluid

    Hoses/Lines & Clamps > Transmission Fluid Cooler Line Hose > Transmission Fluid Cooler Line Hose Adapter. Price: Alternate: No parts for vehicles in selected markets. ... AGS TR985 3/8 Inverted Flare to Rubber Hose - 2 per Bag Info . AGS TR985. 7.94: 0.00: 7.94: Alternate: Quantity: Add to Cart. AGS TR980 3/8 Straight Male to Rubber Hose ...

    Get Price
  • Best way to connect hose to transmission lines |

    2009-12-16 · kurt said: I was thinking about just flaring the end of the steel line and sliding the rubber hose over it and putting a hose clamp on which will give it something to butt up against. Click to expand... I have, a few times, used a double flare tool and only done the first step and slipped a hose over it.

    Get Price
  • Transmission Oil Cooler Hose | O'Reilly Auto Parts

    Shop for the best Transmission Oil Cooler Hose for your vehicle, and you can place your order online and pick up for free at your local O'Reilly Auto Parts. Skip to content 15% OFF 125 use code: HOT15 Online, Ship to Home Only.

    Get Price
  • Transmission line PSI? | Maverick/Comet Forums

    2011-10-24 · Using hose is fine, but - - -, make sure it is rated for transmission duty, bulb the ends of your lines, no kinks or sharp bends in the lines, and finally, make sure your fittings all have the same inside diameter! If you can't get fittings with the same inside diameter, put the smaller one on the outlet port of the transmission.

    Get Price
  • Transmission Oil Cooler Hose - Best

    Compressor Works Transmission Oil Cooler Hose 900105 18. 99. Part # 900105. SKU # 388018. check if this fits your vehicle. check if this fits your vehicle. Free In-Store or Curbside Pick Up. SELECT STORE. Home Delivery. Standard Delivery. Est. Delivery July 29-30. ADD TO CART.

    Get Price
  • How should I patch my transmission cooling line ...

    2016-2-2 · I do not use any rubber lines on any transmission lines unless it is fitted hydraulic line. Do as you wish. But most metal lines that have rubber in them are just cut steel lines with no barbs or anything to help hold the rubber securely.

    Get Price
  • Flexible, Heatproof & Reinforced transmission

    Alibaba.com features heatproof and durable transmission rubber hose for all your varied requirements at competitive, low prices. Explore the entire transmission rubber hose …

    Get Price
  • Can you replace just the rubber hose on a

    I have a transmission cool line that broke loose from its clamp and got a hole rubbed in it by the drivebelt. The only problem is getting the entire line assembly off is near impossible with its location. My question is, since the line is metal with a rubber hose that looks to be crimped on can I just replace the rubber hose?

    Get Price
  • Rubber hose for trans cooling line | Ford Mustang

    2017-2-2 · 465 Posts. #5 • Feb 1, 2017. Its common to use short sections of rubber hose (rated for trans fluid) to connect trans lines into an external cooler, since you need some flexibility to route up through the radiator support. However, the primary lines running from the transmission to the front of the car really should be one piece steel lines.

    Get Price
  • Fluid Cooler Lines - Rubber Transmission Line

    2021-4-12 · Hose, Auto Trans Oil Cooler Hose, Rubber, Part Number: ADO-84318909. Not Yet Reviewed. Estimated Ship Date: Monday 7/19 ... Sunsong Transmission Oil Cooler Lines. Sunsong 5801080 - Sunsong Transmission Oil Cooler Lines. Automatic Transmission Cooler Line, Rubber, Stock, Each. Part Number: SUG-5801080. Not Yet …

    Get Price
  • Transmission Oil Cooler Hose - Ningbo Shijun

    Brake Hose, Fuel Hose, Charging Hose manufacturer supplier in China, offering 3/8 ID Air Brake Rubber Hose Assembly with Fmvss 106, and DOT Truck Parts, Truck Parts 15 FT Nylon Coiled Air Line Set with 1 X 40inch Leads, Truck Parts 15 FT Nylon Coiled Air Line Set with 2 X 12inch Leads and so on.

    Get Price
  • Leaky transmission lines, can I replace with

    2001-7-4 · The hose line quoted is a cloth reinforced blue rubber hose line that is rated for transmission (and power steering) fluid and is rated at 250 psi. The 'push on' fittings don't require a hose clamp! I've run this type fitting on my TH350 without clamps for several years and can verify that they will NOT blow off.

    Get Price
  • Transmission Oil Cooler Line | 624-542 |

    Dorman Products - 624-542 : Transmission Oil Cooler Line. This replacement automatic transmission oil cooler hose is constructed of quality metal and rubber components to ensure leak-free delivery of critical fluid between the transmission and the transmission …

    Get Price
  • Salisbury Online - Insulated Line Hose

    Salisbury Salcor Connector End Line Hose Class 3 Type II 36' x 1.5' Diameter OR150-3C In Stock. Price: 199.50. Salisbury Salcor Connector End Line Hose Class 3 Type II 48' x 1.5' Diameter OR150-4C Call. Price: 269.50. Salisbury Salcor Connector End Line Hose Class 3 Type II 54' x 1.5' Diameter Bulk OR150-45C-B Call.

    Get Price
  • Transmission Line Size | Jeep Wrangler Forum

    2013-7-29 · the rubber hose is 3/8', and the hard line is 3/8' OD, IIRC. ... The hard line part of the transmission cooler lines contains an antidrainback valve. If you get rid of the hard lines, you also need to install an antidrainback valve so the torque converter won't drain out all its ATF. ... - I never found adapters for the rubber line to my new ...

    Get Price
  • Transmission cooling line popping out of radiator

    2020-6-26 · Rubber hose should be okay. Aftermarket add-on coolers are generally connected with rubber hose. Just make sure the hose is rated for transmission fluid/cooler use. It seems people have gotten away with just clamping the rubber hose to the metal lines, but I’d rather see some sort of bead on the tube ends to aid in hose …

    Get Price
  • 5/16 in. Transmission Rubber Hose SER TR516H

    1 天前 · This transmission hose has superior flexibility which allows for easy routing of lines. Use to replace or make repairs on both 5/16 in. and 3/8 in. transmission/oil cooler lines. Hundreds of domestic and foreign applications. Durable triple walled rubber hose. Pressure rated up to 250 psi.

    Get Price
  • Transmission Cooler Line Rubber Hose & Fittings

    94-01 Transmission Cooler Line Rubber Hose & Fittings. Part Number: 479887MPR. Mopar. 54.50.

    Get Price
  • Can you replace just the rubber hose on a

    2008-9-2 · I have a transmission cool line that broke loose from its clamp and got a hole rubbed in it by the drivebelt. The only problem is getting the entire line assembly off is near impossible with its location. My question is, since the line is metal with a rubber hose that looks to be crimped on can I just replace the rubber hose?

    Get Price
  • Best way to connect hose to transmission lines |

    2009-12-16 · Thanks guys.. I ended up going with a 1/4' hose instead of the 5/16' that was there before. It actually made for a tighter fit at the radiator and the steel line. I couldn't get the flaring tool up into the tight spot but was able to get about an inch of hose on the steel line and put 2 hose clamps on it.

    Get Price
  • TR555 - surrauto.com

    2020-10-4 · Rubber Hose IMAGE KITS QTY LINE DESCRIPTION TR516H 15' 5/16' 3/8' 5/16' Transmission Rubber Hose – Universal (use for both 5/16' and 3/8' repairs) 25' roll Line Connectors IMAGE PART# KITS QTY LINE SIZE DESCRIPTION REORDER QTY TR750 1 3/8' Dodge/Jeep Transmission Line 1/pkg

    Get Price
  • Transmission cooling lines---steel or rubber???

    2005-1-22 · Here's a photo. I jumped from the trans to the frame rail with flex line because of the close fit of the trans tunnel to the transmission. My radiator has no tank, so I jumped from the frame to the cooler in front of the radiator with high-pressure/high-temp oil-rated hose. Steel lines are better, of course, but I couldn't turn out of the transmission …

    Get Price
  • How Well Do You Know Hoses? | MOTOR Magazine

    2021-7-25 · Silicone hose does, however, have a much higher upper temperature limit than conventional heater hoses, usually about 350°F vs. 260°F for conventional hoses. This makes it a very good choice when it must run close to hot exhaust components. Take extra care when clamping silicone hoses.

    Get Price
  • ('09-'13) - Transmission Line Size | Subaru

    2015-7-18 · Transmission Line Size ('09-'13) Jump to Latest Follow ... Pull off the (flimsy at best) long rubber hose on the passengers side of lower radiator and fish it under and thru the front of the a/c condenser and into the bottom of the cooler. Tighten clamp. We put a wire nut into the hose to keep the tranny fluid from leaking out. Hold the hose ...

    Get Price
  • Transmission cooler lines | Adventure Rider

    2013-11-4 · I was able to remove the transmission side of the lines. While at the store I loaded up on some pre-made hard line. On the transmission side I used a 2' section of hard line as a nipple to connect rubber hose to. I put a small flair on the line and double hose clamped the rubber line.

    Get Price
  • check your transmission vent hose | Road Glide

    2013-8-18 · Joined Jan 14, 2011. ·. 931 Posts. #5 · Aug 18, 2013. You will probably have to replace it within the first couple yearsif you ride much. it will start to show dry rot and start cracking and disintigrating. pretty easy to replace though, just make sure you get the gasket for the trans cover when you get the hose.

    Get Price
  • Can you replace just the rubber hose on a

    I have a transmission cool line that broke loose from its clamp and got a hole rubbed in it by the drivebelt. The only problem is getting the entire line assembly off is near impossible with its location. My question is, since the line is metal with a rubber hose that looks to be crimped on can I just replace the rubber hose?

    Get Price
  • SAE J1532 300psi Transmission Oil Cooler Line

    Pressure Hose, Cloth Braid Hose, Fiber Hose manufacturer supplier in China, offering SAE J1532 300psi Transmission Oil Cooler Line Rubber Hose, 1sn 2sn Steel Wire Braid Reinforced Flexible Smooth Hydraulic Rubber Hose, Excellent Quality 2sn 1sn Standard Steel Wire Braided Hydraulic Rubber Petroleum Hose Pipe and so on.

    Get Price
  • Ceramic Lined Rubber Pipe for Solid Material

    Bulkbuy Ceramic Lined Rubber Pipe for Solid Material Transmission price comparison, get China Ceramic Lined Rubber Pipe for Solid Material Transmission price comparison from Ceramic Rubber Hose, Rubber Hose manufacturers & suppliers on Video Channel of Made-in-China.com .

    Get Price
  • Transmission Cooler Line Rubber Hose & Fittings

    94-01 Transmission Cooler Line Rubber Hose & Fittings. Part Number: 479887MPR. Mopar. 54.50.

    Get Price
  • Fluid Cooler Lines - Steel/Rubber Transmission

    Fluid Cooler Line, Automatic Transmission, Direct Replacement, Steel/Rubber, Quick-Connect and Flange Ends, 25.4 in. Length, Chrevrolet, GMC, Each Part Number: RNB-624-722 Not Yet Reviewed

    Get Price
  • J1532: Transmission Oil Cooler Hose - SAE

    1995-2-1 · Transmission Oil Cooler Hose. J1532_200503. This SAE Standard covers four types of hose for use with automatic transmission fluid: A, B, AT, and BT. Type A and Type B are for use within a temperature range of -40 to 125 degrees C (-40 to 257 degrees F) while types AT and BT are for use within a temperature range of -40 to 150 degrees C ( …

    Get Price
  • How to Replace a Transmission Hose Going Into

    How to Replace a Transmission Hose Going Into the Radiator ... Older vehicles often have these lines patched with rubber fuel lines. When the line is broken or kinked, the entire line should be replaced. Step 1. Raise the vehicle with a jack and set it on jack stands. Step 2. Locate the transmission cooler line fitting at the back of the ...

    Get Price
  • Transmission Cooler Line Repair Kit | 2006-2010

    PARKER 5/8 AIR BRAKE HOSE #201-10; FITTING 5/8 TUBE -10 HOSE #1T126-10-10; A common area for leaks to occur in an Allison Transmission is at the factory crimp on the OEM installed coolant lines. This is more common in cold weather as the rubber hose on the line shrinks and allows leaks around the factory crimp.

    Get Price
  • Choosing between rubber, metal and metal flex

    2021-7-24 · Provides great flow. Generally lighter weight than rubber hose assemblies. Can handle pressures above 6,000 psi. Generally outlasts rubber hose assemblies. Generally less expensive than rubber or metal flex hose assemblies. Smaller outside diameter than rubber hose assemblies for the same inside diameter result in better …

    Get Price
  • check your transmission vent hose | Road Glide

    2013-8-18 · Joined Jan 14, 2011. ·. 931 Posts. #5 · Aug 18, 2013. You will probably have to replace it within the first couple yearsif you ride much. it will start to show dry rot and start cracking and disintigrating. pretty easy to replace though, just make sure you get the gasket for the trans cover when you get the hose.

    Get Price
  • Can you replace just the rubber hose on a

    2008-9-2 · I have a transmission cool line that broke loose from its clamp and got a hole rubbed in it by the drivebelt. The only problem is getting the entire line assembly off is near impossible with its location. My question is, since the line is metal with a rubber hose that looks to be crimped on can I just replace the rubber hose?

    Get Price
  • Transmission Oil Cooler Rubber Oil Hose Sae

    High quality Transmission Oil Cooler Rubber Oil Hose Sae J1532 ATF High Temperature Braided Net Protective Shell from China, China's leading fuel oil hoses product, with strict quality control nbr rubber hose factories, producing high quality nbr rubber hose products.

    Get Price
  • Automotive Hose | JYM® Rubber Supplier

    2021-7-15 · Automotive hose is an important part of automotive components, making car efficient and dependable. Automotive hoses play an integral role in the operation of automobiles, include flexible air brake hoses, air conditioning hoses, automotive exhaust hoses, power steering hose…. JYM 2020-07-21T08:11:40+00:00.

    Get Price
  • Global Transmission – HOSE MANUFACTURER

    Global Transmission 37, Strand Road, 1st Floor, Kolkata – 700 001, West Bengal India 91 33 4065 3098 [email protected] Read More. Quick Links. Home; Profile; Products; Contact; Profile. Manufacturer, Exporter and importer of Industrial Hose, Carbon free Hose, High Pressure Hoses, Rubber Hose, Hydraulic hose, Metallic hose, Wire ...

    Get Price
  • Transmission Cooler Line Repair Kit | 2006-2010

    PARKER 5/8 AIR BRAKE HOSE #201-10; FITTING 5/8 TUBE -10 HOSE #1T126-10-10; A common area for leaks to occur in an Allison Transmission is at the factory crimp on the OEM installed coolant lines. This is more common in cold weather as the rubber hose on the line shrinks and allows leaks around the factory crimp.

    Get Price
  • Choosing between rubber, metal and metal flex

    2021-7-24 · Provides great flow. Generally lighter weight than rubber hose assemblies. Can handle pressures above 6,000 psi. Generally outlasts rubber hose assemblies. Generally less expensive than rubber or metal flex hose assemblies. Smaller outside diameter than rubber hose assemblies for the same inside diameter result in better …

    Get Price
  • Plugs & Caps for Auto Hoses and Tubing |

    2 天前 · Hoses/Tubing. Below you'll find the StockCap offerings for automotive hose and fitting assemblies. These products have many applications, but work especially well with metal and plastic fluid lines, rubber hoses and fittings as …

    Get Price
  • DAYCO TRANSMISSION OIL COOLER, 250 PSI, 25

    This transmission oil cooler/power steering return line hose measures 25 feet x 11/32 inches. It has one braid, and a working pressure of 250 PSI to get the job done. This transmission oil cooler/power steering return line hose …

    Get Price
  • Chevrolet Silverado 1500 Questions -

    2021-5-18 · transmission line is leaking a radiator, leaking at rubber hose compression, is there a quicker way to repair than total line replacement? 1 Answer. Chevy truck with 200000 miles and runs great. 5.3 engine with lots of power and don't have time or money to replace whole line set.

    Get Price
  • transmission cooler line question | The H.A.M.B.

    2016-1-20 · Rubber cooler lines will not pass Tech at the drags because its going to fail, the cheap transmission coolers come with hose and clamps but they will fail. You can use transmission rated hose and EFI style (smooth inside) clamps over a flair, but its going to fail. OEM lines with crimped on rubber connections fail faster than you can change them.

    Get Price
Inquiry Now